01. TREATEX HARDWAX OIL CLEAR

01. TREATEX HARDWAX OIL CLEAR

AURO 123 PURSOLID HARD OIL (SOLVENT-FREE)

AURO 123 PURSOLID HARD OIL (SOLVENT-FREE)

AURO 126-90 HARD OIL WHITE

AURO 126-90 HARD OIL WHITE

01. TREATEX HARDWAX OIL CLEAR

Protects and enhances the natural beauty of wood. Treatex Hardwax Oil is user friendly, quick drying, easy to maintain and provides a hard wearing and attractive finish. Based on natural sustainable raw materials including jojoba oil, linseed oil, sunflower oil, beeswax, candelilla wax and carnauba wax.

  • Comes in Matt, Satin or Gloss sheen levels (select from box below).
  • Has a warming effect on lighter coloured timbers
  • Easy to apply
  • Quick drying
  • Low odour
  • Water resistant
  • Very durable
As low as £2.50
Availability: In stock
SKU
TRE

Other features

  • No sanding required between coats
  • Withstands high temperatures
  • Very durable
  • Easy to maintain with Treatex Wax Polish
  • Spot repairable
  • R10 slip resistance certified and slip resistant certified for commercial use: DIN-51130, DIN-51131, EN-13893
  • Complies with regulation DIN 68861-1B: Resistance to spills of water, wine, beer, coffee, tea, fizzy drinks etc
  • Safe for use on children’s toys: DIN EN 71-3
  • Meets with VOC emissions regulations
  • Recommended for those with dust allergies; dirt and dust can be removed easily
  • Easy to clean with Treatex Floor Care or Treatex Spray on Floor and Surface Clean

Usage

Suitable for: internal use

Recommended timbers: All (dense/oily timbers may require Treatex Thinner)

Applications: floors, doors, stairs, worktops, woodturning etc.

Preparation:

If the surface to be treated is rough or if a previous surface coating finish (e.g. varnish, lacquer, etc.) is present, sand to smooth bare wood with 80-120 grit sandpaper. Some previously oiled surfaces can be overcoated, without sanding. To check compatibility, a trial application is essential when overcoating a previously oiled surface. Remove dust, dirt and any other contaminates which may lead to uneven absorption of Clear Hardwax Oil. Make sure the surface to be treated is thoroughly dry. Stir tins and ensure product is at room temperature before use. Enough product should be purchased to complete the whole project and when more than one container is required it is advisable to mix them together before use. We strongly recommend a small trial application prior to starting a project.

Application:

If you are treating oily/dense timbers e.g. Iroko, Ipe, Teak, Jarrah, Merbau etc. thin the first coat of Treatex Hardwax Oil Clear by mixing with approximately 10% Treatex Thinner. This enables the product to properly penetrate into these types of timbers. Use a brush or short gloss pile roller to evenly apply Treatex Hardwax Oil allowing roughly 30g per m². On worktops and doors etc. pay particular attention to end grain (on end grain apply wet on wet until product is no longer absorbed by the wood). Allow to dry – maintaining warmth and ventilation will enable the surface to dry within 3-6 hours. Apply with a brush or roller a second coat of Treatex Hardwax Oil, again allowing roughly 30g per m². Allow to dry thoroughly overnight before the surface is lightly used. The surface will reach maximum hardness after a further 24 hours.

Tips:
  • Please Note! Clear Hardwax Oil must always be used as the final coat when Natural Hardwax Oil or Colour Tones are applied*
  • If Treatex Hardwax Oil is applied too thickly, drying time will be increased. To speed up drying time raise the room temperature and increase air flow by opening doors and windows, or using a fan. 
Coverage:

1L will cover approximately 20m² in one coat (depending on the timber and method of application).

1L will cover approximately 3 doors in two coats depending on the timber and method of application.

2.5L will cover approximately 50m² in one coat (depending on the timber and method of application).

2.5L will cover approximately 30m² in two coats depending on the timber and method of application.

Available SizesApprox. coverage m2
1L20
2.5L50

Coverage quoted is approx and may vary due to application or absorbtion from the substrate etc.; figures are for total area one coat would cover.

  • Based on natural sustainable raw materials including jojoba oil, linseed oil, sunflower oil, beeswax, candelilla wax and carnauba wax.