TREATEX CLASSIC COLOUR COLLECTION

TREATEX CLASSIC COLOUR COLLECTION

OSMO WHITE GLOSS (OPAQUE WOOD STAIN) 2104

OSMO WHITE GLOSS (OPAQUE WOOD STAIN) 2104

TREATEX CLASSIC COLOUR COLLECTION

Treatex Classic Colour Collection is a high quality opaque, satin sheen wood finish for internal and extrernal use which has been tried and tested in extreme conditions such as on the coast and in the mountains. This product is manufactured on a base of natural sustainable raw materials including: sunflower oil, soybean oil, beeswax and carnauba wax. Treatex Classic Colour Collection can be used on all types of timber and is the ideal finish for doors, windows, fences, sheds, cladding, kitchen cabinets and other interior or exterior joinery.

As low as £2.50
Availability: In stock
SKU
TRECLASS

Features:

  • Easy to apply

  • High coverage

  • Satin sheen finish

  • UV resitant

  • Will not flake or peel

  • Contains no biocides or preservatives

  • Highly water resistant

  • Safe for use on Children’s toys EN71/3 DIN 53160

  • Can be used in a wide range of applications

Usage/Coverage:

Suitable for: internal and external use
Recommended timbers: All
Applications: doors, windows, fences, sheds, cladding, tables, kitchen cabinets and flooring (2 coats of hardwax oil recommended if using with a floor).

0.5L covers approximately 12.5m² in one coat or 7.5m² in two coats depending on the timber and method of application*
1L covers approximately 25m² in one coat depending on the timber and method of application*

*Rough sawn timbers will increase consumption by a factor of 2 to 3. It is advisable to sand the timber surface first to create a smoother area to apply to OR speak to one of the Team at Treatex to discuss further options to improve coverage.

Preparation/Application:

Preparation: Treatex Classic Colour Collection works best on unfinished timber. Previous porous finishes should be thoroughly cleaned or lightly sanded before overcoating. Flaking or peeling finishes must be fully removed prior to application. A trial application is essential when overcoating another finish. Ensure the timber is dry and free from possible contaminates e.g. algae, grease, dirt, dust etc. Exterior timbers susceptible to decay, mould and fungi should be treated first with Treatex Preservative. To help prevent staining, exterior timbers with high tannin levels (e.g. oak, idigbo, teak, cedar, mahogany) should be treated with Treatex Stain Inhibitor. We advise that when using Treatex Classic Colour Collection, sufficient product is purchased to complete the whole project and when more than one tin is required it is advisable to mix them together before use. Timber must have a moisture content below 18%. Temperature must be between 8 degrees and 25 degrees during application and drying. We strongly recommend a trial application prior to starting the project.

Application: Stir tins thoroughly, before and during use. Use a brush or roller to evenly apply Treatex Classic Colour Collection in the same direction as the wood grain. If possible, apply the first coat to all sides of the wood before installation. Pay particular attention to any end grain. To ensure the timber is fully sealed apply the product liberally on end grain. After approximately 12 hours drying the first coat can be overcoated. Apply with a brush or roller a second coat of Treatex Classic Colour Collection. After the second coat, leave for approximately 12 - 24 hours to dry. A third coat may be needed if applying a light colour on a dark timber. One coat may be enough when renovating previously porous finishes.

Available SizesApprox. coverage m2
0.5L12.5
1.0L25

Coverage quoted is approx and may vary due to application or absorbtion from the substrate etc.; figures are for total area one coat would cover.

  • Manufactured on a base of natural sustainable raw materials including: sunflower oil, soybean oil, beeswax and carnauba wax.